 NEW
in 2009
Niti Wire Bender
The Gold handle tells you its for NiTi Wire!
Special beak design bends NiTi wire with ease and the thin tips enhance the
memory of NiTi wire. Can also be used for stainless steel wires. Made in Germany
and Autoclavable. High Gloss finish with gold handles.
Bends NiTi and stainless steel wires up to .016".
 Mini Size Flush Cut & Safety Hold
DISTAL END CUTTER
The Dentronix E200SNT enables you to cut and hold NiTi and Thermal NiTi wires safely. This new flush cut plier is small enough to reach into the posterior and is designed to hold even the smallest wires securely. Ideal for dry heat sterilization and autoclaves. The GOLD handle tells you it’s for NiTi wire only. When you want to CUT and HOLD NiTi Wire...go for the GOLD!
E200SNT The mini-size distal end cutter “with a spring”.
Cuts and holds NiTi wire from .010” to .018”
Available:
DE200SNT High Gloss Finish DE (Royal)
DSE200SNT - Satin Finish
 Facebow
Plier Set
Designed for head gear appliances… D281 Heavy-duty Wire Cutter easily cuts the
inner and outer bow, while the D282 Wire Bender forms and closes the out bow
loop. Grasps firmly for all adjustments. Both are supplied in a convenient plier
case, and are also sold separately.
Cuts and bends round, square and rectangular facebow wires
up to .070" .
DDS 7000 RAPID
DRY HEAT STERILIZER
When you see the light-you are 100% sure
that your instruments have been sterilized.
 The
"Cycle Complete" light on the Dentronix DDS 7000 assures you that all living micro-organisms on your instruments have been killed.
The DDS 7000 dry heat sterilizer cools instruments inside the unit.
The DDS 7000:
-
Kills spores and all living organisms
-
Has an operating temperature 375° to
420°F
(190°C to 210°C)
-
Eliminates water damage to instruments
-
Keeps instruments sharp longer
-
Exterior of the unit is always safe to touch.
-
Includes plier racks for the sterilization
process
-
Allows an easy transfer system from sterilizer
to chair side
-
Cost effective
-
Cool Down Cycle allows immediate handling of
instruments when sterilization is complete.
-
New HEPA Filter System provides purified air
during cooldown.
-
New light emitting diode (LED) diagnostic
system tells you if your unit is not functioning properly.
-
Easy to install
SPECIFICATIONS
18
3/4"W x 19 3/4 "D x 23 1/8"H
Chamber size: 12
1/2"W x 9"D x 6"H
Capacity: 36
Pliers
Power Requirements: 20A/115V
(10A/230V)
Operating Temperature: 375°
to 410°F (190°C to 210°C)
Controls: Power
on/off cycle start-LED Temp Display
indicators for warm-up, sterilize, cool
down and cycle complete.
Note: Available in 115V (UL Listed) and
230V (bears the CE mark).
| Order # |
| D7000-115 |
| D7000-230 |
ACCESSORY KIT
- D7107
Accessory
Kit
- Includes:
- 4 Plier Racks
- 1 Spore Strip Holder DSSH-1
- 1 MPUS Plus 8 oz. Bottle
- 1 Receptacle 20 amp.
- 1 Spore Test Sample
- 1 Silicone Lubricant
|
Barrier Bags
Protect your sterilized instruments from
airborne contaminants after sterilization.
Clear poly bags are custom fitted
to accommodate the Dentronix rack transfer system,
and allow easy viewing of plier set-up. Bags slide over racked pliers
protecting them until it’s time to use.
Handy adhesive strip seals and can be used for
written identification. Available in three sizes.
Large (fits large racks-250/pkg)
| Order # |
Size |
| DBB-101 |
10
1/2" x 9" |
Medium (fits mini racks-250/pkg)
| Order # |
Size |
| DBB-102 |
7"
X 7 1/2 |
Small (fits scalers, mouth mirrors-150/pkg)
| Order # |
Size |
| DBB-103 |
3
1/2"X 8 1/2" |
|
|
